TGL2927-SM 2 ? ? ? 4 ghz 200 watt vpin limiter datasheet: rev - 06-26-15 - 1 of 9 - disclaimer: subject to change without notice ? 2015 qorvo www.qorvo.com pad configuration pad number symbol 3 rf input 14 rf output 1, 2, 4-13, 15-20 no connection 21 (slug) gnd note: the rf input and output ports are not interchangeable. applications ? receive chain protection ? commercial and military radar ? communications ? electronic warfare general description the qorvo TGL2927-SM is a high- power receive protection circuit (limiter) operating from 2-4 ghz. capable of withstanding up to 200 w incident power levels, the TGL2927-SM allows < 18 dbm flat leakage to pass through and contributes < 0. 6db in insertion loss. using qorvo?s passive gaas vpin technology, the tgl2927- sm does not require bias and is offered in a small 4 x 4 (mm) plastic overmold package. this simplifies system integration while maximizing performance and protection. the tgl2927- sm is ideal for commercial and military ra dar applications where protecting sensitive receive components from damage is critical. lead-free and rohs compliant. evaluation boards available on request. product features ? frequency range: 2 to 4 ghz ? insertion loss: < 0.6 db ? peak power handling: 200 w (pulsed) ? flat leakage: < 18 dbm ? passive (no dc bias required) ? integrated dc block on output ? package dimensions: 4.0 mm x 4.0 mm x 0.85 mm functional block diagram ordering information part eccn description TGL2927-SM ear99 200w s-band vpin limiter TGL2927-SM_evb ear99 200 w s-band vpin limiter eval. board
TGL2927-SM 2 ? ? ? 4 ghz 200 watt vpin limiter datasheet: rev - 06-26-15 - 2 of 9 - disclaimer: subject to change without notice ? 2015 qorvo www.qorvo.com absolute maximum ratings parameter value incident power, pulsed (500 us / 15%) , 50 , 25 c 54.0 incident power, pulsed (500 us / 15%) , 50 , 85 c 50.5 mounting temperature (30 sec.) 260 c storage temperature -55 to 150 c operation of this device outside the parameter rang es given above may cause permanent damage. these are stress ratings only, and functional operation of th e device at these conditions is not implied. recommended operating conditions parameter value passive ? no bias ----- electrical specifications are measured at specified test conditions. specifications are not guaranteed over all operating conditions. electrical specifications test conditions unless otherwise noted: 25 c, s-p arameters cw, power pulse parameters: pw = 500 us, duty cycle = 15% parameter min typical max units operational frequency range 2 4 ghz insertion loss (2.0 ? ? ? 4.0 ghz) < 0.6 db insertion loss (4.0 ? ? ? 4.5 ghz) < 0.9 db input return loss 15 db output return loss 15 db flat leakage power at p in > 30 dbm < 18 dbm insertion loss temperature coefficient -0.001 db/c thermal and reliability information parameter test conditions value units incident power (rf operational life test 168 hours (1) ) frequency = 3.3 ghz, pulsed, pw = 100 us, dc = 10%, 50 , 25 c 200 w notes: 1. test was terminated at 168 hours. insertion loss remained 1 db for device under test.
TGL2927-SM 2 ? ? ? 4 ghz 200 watt vpin limiter datasheet: rev - 06-26-15 - 3 of 9 - disclaimer: subject to change without notice ? 2015 qorvo www.qorvo.com typical performance test conditions unless otherwise noted: 25 c, s-p arameters cw, power pulse parameters: pw = 500 us, duty cycle = 15% -2.0 -1.8 -1.6 -1.4 -1.2 -1.0 -0.8 -0.6 -0.4 -0.2 0.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 s21 (db) frequency (ghz) gain vs. frequency vs. temp. -40 c +25 c +85 c 0 2 4 6 8 10 12 14 16 18 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 output power (dbm) input power (dbm) ouput power vs. input power vs. freq. 2.0 ghz 2.5 ghz 3.0 ghz 3.5 ghz 4.0 ghz temp. = 25 c cw input power -30 -25 -20 -15 -10 -5 0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 s11 (db) frequency (ghz) input return loss vs. freq. vs. temp. -40 c +25 c +85 c 10 11 12 13 14 15 16 17 18 19 20 29 31 33 35 37 39 41 43 45 47 49 51 53 55 leakage power (dbm) input power (dbm) output power vs. input power vs. temp -40 c +25 c +85 c frequency = 3.5 ghz -30 -25 -20 -15 -10 -5 0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 s22 (db) frequency (ghz) output return loss vs. freq. vs. temp. -40 c +25 c +85 c 10 11 12 13 14 15 16 17 18 19 20 29 31 33 35 37 39 41 43 45 47 49 51 53 55 output power (dbm) input power (dbm) output power vs. input power vs. freq. 3.0 ghz 3.5 ghz 4.0 ghz
TGL2927-SM 2 ? ? ? 4 ghz 200 watt vpin limiter datasheet: rev - 06-26-15 - 4 of 9 - disclaimer: subject to change without notice ? 2015 qorvo www.qorvo.com pad description note: the rf input and output ports are not interch angeable. pad no. symbol description 1, 2, 4 ? ? ? 13, 15 ? ? ? 20 no connection no connection. recommend connecting to gnd at evb l evel 3 rf input rf input; matched to 50 ; dc coupled 14 rf output rf output; matched to 50 ; dc blocked 21 (slug) gnd on pcb, multiple vias should be employed under the center pad (21) to minimize inductance and thermal resistance; see pag e 5 for suggested mounting configuration.
TGL2927-SM 2 ? ? ? 4 ghz 200 watt vpin limiter datasheet: rev - 06-26-15 - 5 of 9 - disclaimer: subject to change without notice ? 2015 qorvo www.qorvo.com evaluation board and mounting detail rf layer is 0.010? thick rogers corp. ro4003c, r = 3.38. metal layers are 0.5 oz. copper. the micro strip line at the connector interface is optimized for the southwest microwave end launch connector 1092-02a-5. the trace pattern shown has been developed and test ed for optimized assembly at triquint semiconductor . the pcb land pattern has been developed to accommodate lead tolerances. since processes vary from company to company, careful process development is recommended . for pulsed applications only. increased pulse width and/or duty cycle results in lower power handling capability of the evb. notes: 1. ground / thermal vias under the dut are critical for the proper performance of this device. 2. the evb shown herein utilizes copper filled vias (10 mil diameter) under the dut to maximize heat t ransfer away from the dut under large signal conditions. 3. thermal dissipation is low for normal non-limiti ng operation.
TGL2927-SM 2 ? ? ? 4 ghz 200 watt vpin limiter datasheet: rev - 06-26-15 - 6 of 9 - disclaimer: subject to change without notice ? 2015 qorvo www.qorvo.com mechanical information units: inches tolerances: unless specified .xx = 0.05 .xxx = 0.127 materials: lid: plastic plating: all metalized features are nipdau plated part is lead-free/pohs-compliant; mold encapsulated marking: 2927: part number yy: part assembly year ww: part assembly week xxxx: batch id
TGL2927-SM 2 ? ? ? 4 ghz 200 watt vpin limiter datasheet: rev - 06-26-15 - 7 of 9 - disclaimer: subject to change without notice ? 2015 qorvo www.qorvo.com recommended soldering temperature profile
TGL2927-SM 2 ? ? ? 4 ghz 200 watt vpin limiter datasheet: rev - 06-26-15 - 8 of 9 - disclaimer: subject to change without notice ? 2015 qorvo www.qorvo.com product compliance information esd sensitivity ratings caution! esd-sensitive device esd rating: tbd value: tbd test: human body model (hbm) standard: jedec standard jesd22-a114 solderability compatible with the latest version of j-std-020 lea d free solder, 260 c. this part is compliant with eu 2002/95/ec rohs directive (restrictions on the use of certain hazardous substances in electrical and electronic equipment). rohs compatibility this product also has the following attributes: ? lead free ? halogen free (chlorine, bromine) ? antimony free ? tbbp-a (c 15 h 12 br 4 0 2 ) free ? pfos free ? svhc free msl rating tbd at 260 c convection reflow the part is rated moisture sensitivity level tbd jedec standard ipc/jedec j-std-020. eccn u.s. department of commerce: ear99
TGL2927-SM 2 ? ? ? 4 ghz 200 watt vpin limiter datasheet: rev - 06-26-15 - 9 of 9 - disclaimer: subject to change without notice ? 2015 qorvo www.qorvo.com contact information for the latest specifications, additional product i nformation, worldwide sales and distribution locati ons, and information about triquint: web: www.qorvo.com tel: +1.972.994.8465 email: info-sales@qorvo.com fax: +1.972.994.8504 for technical questions and application information : email: info-products@qorvo.com important notice the information contained herein is believed to be reliable. qorvo makes no warranties regarding the information contained herein. qorvo assumes no responsibility or liability whatsoever f or any of the information contained herein. qorvo assumes no responsibility or liability whats oever for the use of the information contained here in. the information contained herein is provided "as is, where is" and with all faults, and the entire risk associated wit h such information is entirely with the user. all information contained herein is subject to chan ge without notice. customers should obtain and verify the latest relevant information before p lacing orders for qorvo products. the information contained herein or any use of such information does no t grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual property rights, whether with re gard to such information itself or anything describ ed by such information. qorvo products are not warranted or authorized for use as critical components in medical, life-saving , or life- sustaining applications, or other applications where a failure would reasonably be expected to cause severe perso nal injury or death.
|
